CHANGXUN | Valve Test Equipment

Home / Valve Test Benches / How to test a gate valve

How to test a gate valve — shell test, seat test, and the two mistakes that spoil both

A gate valve is the easiest valve to clamp and the hardest one to test honestly, because its disc sits between two seats and a careless fixture lets the pressure go somewhere other than the casting. This page gives the sequence we recommend to every workshop running gate valves on a bench: what to compute first, how to set the gate for each test, how to read the leakage, and what a one-sided failure is telling you.

Gate valvesShell 1.5 × ratingSeat 1.1 × ratingBoth directions

Get a quotation  Send your DN range + PN class

Quick answer

Shell test1.5 × 38 °C rating, gate half open
Seat test1.1 × rating, gate closed, read from the open end
DirectionsBoth — a gate valve has two seats
MediumWater for shell; air optional for resilient seat
BenchHorizontal for DN350+ and long bodies
BackseatOnly if the PO asks for it

Why a gate valve is not tested like a butterfly valve

A butterfly valve is a single disc that seals on a bore; pressurise one side and you have tested everything in one go. A gate valve is a wedge travelling between two seat faces, with a body cavity on each side of it, a bonnet joint above, and a stuffing box around the stem. That geometry changes the test in four ways.

There are two seats, not one. A double-disc gate valve has two independent sealing faces and a resilient-seated valve has two rubber-faced seats. They fail separately, so the seat test has to be run twice, once from each direction, with the leakage read at the opposite end. One pass is not a result.

The gate position changes what is under pressure. With the gate closed, the shell pressure acts on the disc as well as the body, the wedge is pushed hard against one seat, and a leak path past the seat is hidden behind the test itself. With the gate half open, the pressure reaches the whole body cavity and both seat faces evenly — which is what the shell test is meant to verify. This single detail is where most workshop procedures go wrong.

Gate valves are long. Face-to-face dimensions run well beyond those of a butterfly valve of the same bore, so the clear span between sealing plates and the travel of the clamping ram matter more than the tonnage. Long bodies also sit awkwardly on a vertical bench, which is why large gate valves are almost always tested horizontally.

Seat pockets collect debris. The recess behind each seat traps casting sand, scale and machining chips. A valve that passed at the factory can leak on the first test after transport because a chip has settled on a seat face — a flush and a re-test fixes it, and it is not a manufacturing defect.

Before you pressurise: two numbers and one look at the nameplate

  1. Read the nameplate, not the drawing. You need the size (DN or NPS), the pressure class (PN or Class), the body material, the seat type (metal or resilient) and the standard named on the purchase order. The standard decides the acceptance criteria; the nameplate decides the pressure.
  2. Compute the two pressures. Shell test = 1.5 × the 38 °C rating; seat test = 1.1 × the same rating. PN16 becomes 2.4 MPa and 1.76 MPa; PN40 becomes 6.0 MPa and 4.4 MPa; PN100 becomes 15 MPa and 11 MPa. Do the multiplication before the valve goes on the bench, not while the gauge is climbing. The full PN10–PN400 table is on the hydrostatic test pressure chart.
  3. Check the hold time for that size. The minimum duration in API 598 grows with nominal size, from a few seconds at NPS 2 to several minutes at DN600, and project specifications often ask for longer. The chart page lists the durations by size band.
  4. Look inside the bore. Gate valve, half open, torch through the bore: chips, sand or rust on a seat face will fail the test no matter how good the bench is. Flush first, then clamp.

The test, step by step

  1. Mount horizontally, sealed at both flanges. Blind plates or flange adapters on both ends, valve centred so the clamping force passes through the body and not through the bonnet. Do not clamp on the bonnet or the stem; those are the two places a gate valve bends.
  2. Open the gate a quarter to a half. Confirm on the stem indicator, not by counting handwheel turns. The disc must be clear of both seats for the shell test.
  3. Fill and vent. Fill with water, open the highest vent until water runs clear, then close it. Trapped air cushions the pressure rise, makes the gauge jump, and turns a pinhole into a false pass.
  4. Pressurise in two stages. Take it to about half the shell pressure, hold briefly and walk the body: body-bonnet joint, gland, flange faces, casting. Then raise to full shell pressure and hold for the specified time. A casting defect usually shows as a slow sweat on the surface, not a jet.
  5. Depressurise and close the gate fully. Read the closed position from the stem, and check the bore from the far end if the design allows.
  6. Seat test, direction one. Apply 1.1 × rating to one side only, leave the other side open to atmosphere with a clean drain, and collect what comes through for the specified period. Measure it — a graduated cylinder over one minute, or a bubble count if the specification is written in bubbles per minute. Do not judge by eye.
  7. Seat test, direction two. Reverse the pressure and repeat. On a double-disc gate valve this is not a formality: the downstream disc is a separate part with its own seat face, and it can fail alone.
  8. Backseat test, if specified. Valve fully open, packing gland released, pressure applied to the backseat. This verifies that the stuffing box can be repacked with the line under pressure. Skip it if the PO is silent — it is not part of the standard sequence.
  9. Record, drain, dry, protect. Log pressure, hold time, leakage volume, water temperature and operator. Drain and dry the cavity; a gate valve shipped wet rusts in the seat pocket and arrives leaking.

Reading the result: what each failure usually is

What you seeMost likely causeWhat to do
Slow sweat on a casting, no dripPorosity in the body castingReject. Wet the surface and watch — porosity weeps, a joint drips
Drip at the body–bonnet jointGasket seating, bolt torque, or a damaged gasketDepressurise, re-torque in a cross pattern, re-test; if it returns, replace the gasket
Leak at the glandPacking not compressed, lantern ring misplacedRe-pack and set the gland evenly, a quarter turn at a time
Seat leak on one side onlyScratch or wire-drawn groove on that seat face; chip in the seat pocketFlush and re-test first; if it repeats, the seat face needs lapping
Leak on both seat testsGate not fully closed, travel stop mis-set, obstruction under the wedgeCheck the stem position and the bore before blaming the seats
Gauge falls with the valve closedLeaking isolation valve, pump check or vent on the benchTest the rig empty with a blind plate — the fault is upstream of the valve

Acceptance depends on the seat type. A resilient-seated gate valve is normally expected to show no visible leakage. A metal-seated valve is accepted against a leakage-rate class instead, because metal on metal does not seal to zero — the classes and how they are counted are explained on the API 598 and ISO 5208 leakage rate classes page. Getting this wrong in either direction costs money: too strict a criterion scraps good valves, too loose a one ships a claim.

Which bench does a gate valve need

The pressure class sets the pump and the frame; the size sets the plates, the span and the clamp. For gate valves the span is the part buyers underestimate, because the body is long and the plates have to sit outside the flanges. A bench quoted on tonnage alone will be short on daylight at DN400 and above. How the clamping force is generated and where it is applied is covered on the clamping methods page.

SYJ-150 · small gate valves

  • DN15 – DN150
  • Water 0 – 40 MPa
  • 30-ton clamping
View SYJ-150 →

ZSYJ-300A · mid range, high class

  • DN50 – DN300
  • 1.6 – 40 MPa
  • 80-ton clamping, PLC
View ZSYJ-300A →

WBD-600 · long bodies, large bore

  • DN50 – DN600
  • Water 0 – 16 MPa
  • 150-ton end clamp
View WBD-600 →

SYJ-600SQ · water + air

  • DN50 – DN600
  • Water 40 MPa / Air 4 MPa
  • 90-ton clamping
View SYJ-600SQ →

Two worked cases. A workshop testing DN50–DN200 gate valves up to PN100 needs 15 MPa on a small plate — pressure, not tonnage — and either the SYJ-150 or the ZSYJ-300A covers it. A workshop testing DN400–DN600 gate valves at PN16 needs only 2.4 MPa but a 150-ton clamp and roughly 1.2 m of clear span, which is the WBD-600 case. The same page of the buyer guide walks through the selection logic from pressure to throughput, and the eight-step hydrostatic test procedure covers the general sequence for every valve type.

Questions we get asked about gate valve testing

Should the gate be open or closed during the shell test?

Half open. The disc has to be off both seats so the body cavity, bonnet and both seat faces see shell pressure together. Tested closed, the wedge splits the body in two and hides any leak behind the seat.

Why does it hold on one side and leak on the other?

Two seats, two sealing faces, tested separately. A one-sided leak is mechanical — a scratch, a wire-drawn groove, or debris in the seat pocket on that side — and reversing the valve in the fixture should reproduce it on the same side.

What pressure do I use for a Class 300 gate valve?

Take the 38 °C rating for the size from the applicable ASME table, then apply the same factors: 1.5 × for shell, 1.1 × for seat. The factors are the API 598 ones; the rating comes from the class table, not from the PN series.

Do I need a backseat test?

Only if the PO or project specification calls for it. Fully open valve, gland released, pressure on the backseat — it proves the stuffing box can be repacked under pressure. Common on steam and high-temperature gate valves, unusual on water service.

Can I use air for the shell test?

No. The shell test is hydrostatic because compressed gas stores energy and a failure is dangerous. Air is for the low-pressure seat tightness test on resilient-seated valves, and needs a bench with a separate air circuit.

How long does one gate valve take?

On a manual bench, one valve of DN200 at PN16 is roughly ten minutes of work: mounting, filling, venting, the shell hold, two seat holds and draining. On a PLC bench the holds are timed and logged automatically, and the operator time drops to loading and inspection — which matters when gate valves arrive in batches of fifty.

Tell us the DN range, the pressure class and the valve types — we will name the bench and the plate set

Send the size band and the classes on your orders. You get a model recommendation, a datasheet, the fixture drawing and a price within 12 working hours.

Request a quotation