Changxun Machinery Prices  |  Get a quote  |  +86 134 0908 0470

Questions buyers ask before ordering a valve test bench

These are the twelve questions that come up in almost every enquiry. Each answer gives the conclusion first, then the number or the standard behind it.

Sizing the machine

1. How do I know which DN range I need?

Not the largest valve you have ever seen - the largest valve you will test on this bench in the next five years. Clamping force and frame size follow that number, and so does the price. A workshop topping out at DN200 does not need a DN600 frame.

If you are between two sizes, take the larger one: the frame cannot be extended later, but a large frame tests small valves perfectly well.

2. The pressure range says 1.6 to 40 MPa. Does that mean 40 MPa on every valve?

No. 40 MPa is the design limit of the machine and it is used on small bores. On DN350 - DN600 the valve body is tested at the pressure its class requires, normally up to 16 MPa. Clamping force grows with bore and pressure, so it is calculated together with the pressure you need.

3. Single gauge or dual gauge - what is the difference?

Every bench we build covers 1.6 to 40 MPa. What changes is how many gauge sets sit on it:

The prices published on our price page are for the single gauge version. If you test both ends, say so and the quotation will show the dual gauge price instead.

4. Water test, air test, or both?

Hydrostatic (water) test is the standard for valve body and seat tightness. Air test is used where the specification calls for it, or where a water test would leave residue - gas service, cryogenic, some offshore packages. If you need both on one machine, the water and air model does both without a second clamping.

Testing and records

5. Which test standard does the bench follow?

The machine supplies pressure, holds it and records the curve; the acceptance criteria come from the standard you work to. In practice our customers test to ISO 5208, EN 12266-1 or GB/T 13927 for seat tightness, and to the pressure-hold times those standards specify for the valve size and class. Tell us the standard and the hold time, and we set the PLC accordingly.

6. How long does one valve take?

Clamping is hydraulic - no bolts, no slings, no crane. A valve goes in, clamps, fills, pressurises, holds, drains and comes out; the operator handles the valve, the machine handles the rest. Shops testing in volume usually settle at a few minutes per valve including the printed record.

7. Can the bench produce a test certificate per valve?

Yes. The PLC logs the pressure curve for each test and the file can be exported, so a repaired or new valve leaves the workshop with its own record - the date, the pressure reached, the hold time, the curve. For a valve service shop this is usually the reason to buy a logging bench instead of a bare press.

Site, power and delivery

8. What power supply does it need?

Standard build is 380 V / 50 Hz three phase, or 440 V / 60 Hz for the Americas. Give us your site voltage when you order and the electrical panel is built to it - changing it afterwards is the expensive way.

9. What floor space and foundation do I need?

A vertical bench stands in roughly the footprint of the largest valve plus the frame; a horizontal bench needs length for the ram travel and room to lay the valve down. We send the general arrangement drawing with the quotation so your people can check the door width, the crane path and the floor before the machine ships.

10. Delivery, packing and installation?

Export wooden case, FOB Qingdao, 35 - 55 days depending on model. Operation manual in English, electrical drawing, and one set of seals ship with the machine. Commissioning support by video is included; an engineer visit is available at cost. Every machine is run with a valve in our Zibo workshop before it is packed, and that test record ships with it.

11. What about spare parts and wear items?

Seals and clamping jaws are the wear items and we keep them in stock. We keep the drawings of every machine we have shipped, so a bench from 2012 can still be supplied with the right seal kit. Warranty is 12 months from commissioning or 18 months from shipment, wear parts excluded.

12. What is the minimum order and how do I get an exact price?

One set. The prices of the three models most workshops order are published on the price page. Send your DN range and pressure class and you get the exact figure for your configuration.

Two numbers fix the price: the DN range you test most often, and the pressure class. Send those and you get the model, the exact figure and the delivery date the same working day.

Still two numbers away from a price

Largest DN you test, highest pressure class you test. That is all we need to answer with a model, a price and a delivery date.

Send the two numbers See the published prices